Evaporation is a type of vaporization of a liquid that occurs from the surface of a liquid into a gaseous phase that is not saturated with the evaporating substance. The other type of vaporization is boiling, which, instead, occurs within the entire mass of the liquid and can also take place when the vapor phase is saturated, such as when steam is produced in a boiler. Evaporation that occurs from directly from the solid phase, as commonly observed with ice or moth crystals (naphthalene or paradichlorobenzine), is called sublimation.
On average, a fraction of the molecules in a glass of water have enough heat energy to escape from the liquid. Water molecules from the air enter the water in the glass, but as long as the relative humidity of the air in contact is less than 100% (saturation), the net transfer of water molecules will be to the air. The water in the glass will be cooled by the evaporation until an equilibrium is reached where the air supplies the amount of heat removed by the evaporating water. In an enclosed environment the water would evaporate until is saturates the air.
With sufficient temperature, the liquid would turn into vapor quickly (see boiling point).
When the molecules collide, they transfer energy to each other in varying degrees, based on how they collide. Sometimes the transfer is so one-sided for a molecule near the surface that it ends up with enough energy to ‘escape’.
The Essay on Landfills Leaks Into The Ground Water People Make Air
Did you know that we have a BIG problem in our world? The problem is that there is too much waste being produced by humans. Waste is left over material like paper, lunch bags, cans, bottles, plastic bags, wood and metal. Waste is stuff we throw into the garbage because we do not want to use it no more. It's stinky and filling up the landfill sites. We are littering and polluting the land, water ...
Evaporation is an essential part of the water cycle. The sun (solar energy) drives evaporation of water from oceans, lakes, moisture in the soil, and other sources of water. In hydrology, evaporation and transpiration (which involves evaporation within plant stomata) are collectively termed evapotranspiration. Evaporation of water occurs when the surface of the liquid is exposed, allowing molecules to escape and form water vapor; this vapor can then rise up and form clouds.
* |
Theory
See also: Kinetic theory
For molecules of a liquid to evaporate, they must be located near the surface, be moving in the proper direction, and have sufficient kinetic energy to overcome liquid-phase intermolecular forces.[1] When only a small proportion of the molecules meet these criteria, the rate of evaporation is low. Since the kinetic energy of a molecule is proportional to its temperature, evaporation proceeds more quickly at higher temperatures. As the faster-moving molecules escape, the remaining molecules have lower average kinetic energy, and the temperature of the liquid decreases. This phenomenon is also called evaporative cooling. This is why evaporating sweat cools the human body. Evaporation also tends to proceed more quickly with higher flow rates between the gaseous and liquid phase and in liquids with higher vapor pressure. For example, laundry on a clothes line will dry (by evaporation) more rapidly on a windy day than on a still day. Three key parts to evaporation are heat, atmospheric pressure (determines the percent humidity) and air movement.
On a molecular level, there is no strict boundary between the liquid state and the vapor state. Instead, there is a Knudsen layer, where the phase is undetermined. Because this layer is only a few molecules thick, at a macroscopic scale a clear phase transition interface can be seen.
The Essay on A Study of Azeotrope and Acetone/Chloroform Liquid-Vapor Phase Diagram
A Study of Azeotrope and Acetone/Chloroform Liquid-Vapor Phase Diagram Abstract: Liquid-vapor phase of acetone/chloroform was studied through distilling a series of mixtures with different mole fraction. When the mixtures were boiling, their vapor was condensed through a water column and collected in a receiving container. Refractive index was collected for starting mixture, distillate and residue ...
Liquids that do not evaporate visibly at a given temperature in a given gas (e.g., cooking oil at room temperature) have molecules that do not tend to transfer energy to each other in a pattern sufficient to frequently give a molecule the heat energy necessary to turn into vapor. However, these liquids are evaporating. It is just that the process is much slower and thus significantly less visible.
Evaporative equilibrium
Vapor pressure of water vs. temperature. 760 Torr = 1 atm.
If evaporation takes place in an enclosed area, the escaping molecules accumulate as a vapor above the liquid. Many of the molecules return to the liquid, with returning molecules becoming more frequent as the density and pressure of the vapor increases. When the process of escape and return reaches an equilibrium,[1] the vapor is said to be “saturated,” and no further change in either vapor pressure and density or liquid temperature will occur. For a system consisting of vapor and liquid of a pure substance, this equilibrium state is directly related to the vapor pressure of the substance, as given by the Clausius-Clapeyron relation:
where P1, P2 are the vapor pressures at temperatures T1, T2 respectively, ΔHvap is the enthalpy of vaporization, and R is the universal gas constant. The rate of evaporation in an open system is related to the vapor pressure found in a closed system. If a liquid is heated, when the vapor pressure reaches the ambient pressure the liquid will boil.
The ability for a molecule of a liquid to evaporate is based largely on the amount of kinetic energy an individual particle may possess. Even at lower temperatures, individual molecules of a liquid can evaporate if they have more than the minimum amount of kinetic energy required for vaporization.
Factors influencing the rate of evaporation
Note: Air used here is a common example; however, the vapor phase can be other gasses.
Concentration of the substance evaporating in the air
If the air already has a high concentration of the substance evaporating, then the given substance will evaporate more slowly.
Concentration of other substances in the air
If the air is already saturated with other substances, it can have a lower capacity for the substance evaporating[citation needed].
The Essay on Property Diagrams Of Pure Substances
* Characteristics by which physical properties of system may be described. e.g. pressure, volume, temperature, entropy, enthalpy etc. * Properties are the coordinates by which state of the system is described. * Any operation in which one or more properties of system may change is called change of state. * Thermodynamic properties are of two types : Extensive properties- that depend on mass of the ...
Flow rate of air
This is in part related to the concentration points above. If fresh air is moving over the substance all the time, then the concentration of the substance in the air is less likely to go up with time, thus encouraging faster evaporation. This is the result of the boundary layer at the evaporation surface decreasing with flow velocity, decreasing the diffusion distance in the stagnant layer.
Inter-molecular forces
The stronger the forces keeping the molecules together in the liquid state, the more energy one must get to escape. This is characterized by the enthalpy of vaporization.
Pressure
Evaporation happens faster if there is less exertion on the surface keeping the molecules from launching themselves.
Surface area
A substance that has a larger surface area will evaporate faster, as there are more surface molecules that are able to escape.
Temperature of the substance
If the substance is hotter, then its molecules have a higher average kinetic energy, and evaporation will be faster.
Density
The higher the density the slower a liquid evaporates.
In the US, the National Weather Service measures the actual rate of evaporation from a standardized “pan” open water surface outdoors, at various locations nationwide. Others do likewise around the world. The US data is collected and compiled into an annual evaporation map.[2] The measurements range from under 30 to over 120 inches (3,000 mm) per year.
Endothermicity
Evaporation is an endothermic process, in that heat is absorbed during evaporation.
Applications
* Industrial applications include recovering salts from solutions and drying a variety of materials such as lumber, paper, cloth and chemicals.
* When clothes are hung on a laundry line, even though the ambient temperature is below the boiling point of water, water evaporates. This is accelerated by factors such as low humidity, heat (from the sun), and wind. In a clothes dryer, hot air is blown through the clothes, allowing water to evaporate very rapidly.
The Essay on Pollution Air Water Wastes
Pollution has become a major issue over the years. It has caused death, disease, and many health problems. It is a major concern of our world today and not much is being done to prevent it. If not all, a lot of pollution is caused by humans. There are different types like industrial, agricultural, etc. Many people are realizing now the threat that pollution poses to humans. There are three main ...
* The Matki/Matka, a traditional Indian porous clay container used for storing and cooling water and other liquids.
* The botijo, a traditional Spanish porous clay container designed to cool the contained water by evaporation.
* Evaporative coolers, which can significantly cool a building by simply blowing dry air over a filter saturated with water.
Combustion vaporization
Fuel droplets vaporize as they receive heat by mixing with the hot gases in the combustion chamber. Heat (energy) can also be received by radiation from any hot refractory wall of the combustion chamber.
Pre-combustion vaporization
The catalytic cracking of long hydro-carbon chains into the shortest molecular chains possible, vastly improves gasoline mileage and provides reduced pollutant emissions once the fuel vapor is at its optimum ratio with air. The chemically correct air/fuel mixture for total burning of gasoline has been determined to be 15 parts air to one part gasoline or 15/1 by weight. Changing this to a volume ratio yields 8000 parts air to one part gasoline or 8,000/1 by volume. Theoretically, a homogenous mixture can yield gas mileage in excess of 300 miles per gallon, however the actual fuel mileage is highly dependent on the weight of the vehicle.
Film deposition
Main article: Evaporation (deposition)
Thin films may be deposited by evaporating a substance and condensing it onto a substrate.
