In this experiment we are going to get a better understanding of chemical stoichiometry. We are going to be reacting sodium bicarbonate (NaHCO3) and sodium carbonate (Na2CO3) with hydrochloric acid (HCl).
To start off the mass of two unknown substances (being the sodium bicarbonate and sodium carbonate) will be taken. We will need to construct balanced equations for both of the reactants with the HCl and use this to guide us to figure out how much HCl will be needed to react with each of the unknown substances. When this part is through we will then need to find the percent yield (actual yield/theoretical yield x 100).
Determining the mass of sodium chloride at the end of the experiment is the actual yield. To find the theoretical yield we will need to heat the sodium chloride so that all the CO2 evaporates and that will leave us with the theoretical yield of sodium chloride.
Chemical Reactions
NaHCO3 + HCl = NaCl + H20 + CO2
Na2CO3 + HCl = 2NaCl + H2O + CO2
Theoretical yields
.15g NaHCO3 (1mol NaHCO3/84.0059g NaHCO3) (1mol HCl/1mol NaHCO3) (58.44gNaCl/1molNaCl) = .1043 g NaCl .15g Na2CO3 (1mol Na2CO3/105.988g Na2CO3) (1mol HCl/1mol Na2CO3) (58.44gNaCl/1molNaCl) = .165 g NaCl
Experimental Procedure
Standardization of Unknown 1
1) Weigh duplicate 0.15 g samples of unknown 1. Dissolve samples in 100- ml distilled water. 2) Add bromocresol green indicator, until the solution turns into blue. Titrate it with HCl until green color is reached. 3) Heat and boil out CO2 gently. You should obtain a blue color again at the end of this step. Cool to room temperature, and continue titration until yellow color is reached. Note down the volume seen on the buret. 4) Heat the substance again until all the liquid is gone and you’re left with salt looking particles inside the beaker. 5) Weigh the beaker with the salt inside of it. Then, clean out the beaker thoroughly and weigh the empty beaker again. Use these two weights to find the mass in grams of the salt like particles that were previously in the beaker.
The Essay on Sodium Chloride Oxygen Beaker Enzyme
DESCRIPTIVE TITLE The Effect of Different Amounts of Sodium Chloride on the displacement of oxygen. INTRODUCTION The dependability of the rate of an enzyme-mediated reaction is based on two factors: the substrate concentration and the concentration and action of the enzyme that catalyzes the reaction (Vander, et. al. , 2001). Enzymes are catalysts that produce chemical reactions in cells. Enzymes ...
Standardization of Unknown 2
1) Weigh duplicate 0.15 g samples of unknown 1. Dissolve samples in 100- ml distilled water. 2) Add bromocresol green indicator, until the solution turns into blue. Titrate it with HCl until green color is reached. 3) Heat and boil out CO2 gently. You should obtain a blue color again at the end of this step. Cool to room temperature, and continue titration until yellow color is reached. Note down the volume seen on the buret. 4) Heat the substance again until all the liquid is gone and you’re left with salt looking particles inside the beaker. 5) Weigh the beaker with the salt inside of it. Then, clean out the beaker thoroughly and weigh the empty beaker again. Use these two weights to find the mass in grams of the salt like particles that were previously in the beaker. Now to identify which substance is NaHCO3 and which is Na2CO3 pay close attention the mass recorded for the salt like particles that were left in the beaker. The one that is closest to .1043 g is the NaHCO3 and the one closest to .165 g is the Na2CO3.
Results
Grams recorded for Unknown 1- .07 g Unknown 1=NaHCO3 Percent yield= 67% Grams recorded for Unknown 2- .14 g Unknown 2= Na2CO3 Percent yield= 85%
Discussion
When trying to identify which unknown substance was NaHCO3 and which was Na2CO3. We had to make sure to titrate and treat each unknown with the same amount of attention. By over titrating one of the unknowns we could have messed up the experiment and would have had to start over. When heating the liquid on the hot plate, we were making all the CO2 in the liquid evaporate leaving us with just the salt like particles that we were looking for. By weighing the salt we were able to justify what the substance was because of previous conversions that we had worked out.
The Essay on Investigating Stoichiometry With Sodium Salts Of Carbonic Acid
Introduction – The objective of this lab is to better understand Stoichiometry by investigating sodium salts in carbonic acids. Stoichiometry is the study of the amounts of substances that are involved in reactions. This could be either before the reaction takes place or after the reaction takes place. For this lab the reactants are NaHCO3 + HCl and Na2CO3 + HCL and the products are NaCl + ...
Conclusion
The purpose of this experiment was to show how titrating a substance can help to identify that substance. Knowing how to work with stoichiometry equations is also a big part of this lab because we used those equations to help us compare and figure out the identity of the substance. After titrating and evaporating the CO2, the weight of unknown 1 was .07 g which was closest to the theoretical yield of .1043 g. Unknown 1 was identified as NaHCO3. After titrating and evaporating the CO2, the weight of unknown 2 was .14 g which was closest to the theoretical yield of .165 g. Unknown 2 was identified as Na2CO3.
