1. Label 7 of the dishes with the names of the following products: Sulfur, Iron, Sodium Bicarbonate, Sodium Chloride, Sugar, Sand, and Magnesium. Place small samples of each in the appropriate dishes.
2. Examine each sample with a magnifying glass and magnet and record your observations in the data table.
3. Put small samples of each substance in a test tube along with 3 mL of water to determine their solubility.
4. Mix some of the Iron and Sulfur on a clean disposable dish and examine the mixture with a magnifying glass and magnet. Record your observations in the data table. Save and label this mixture.
5. Mix some of the sand and Sodium Chloride on a clean disposable dish and examine the mixture with a magnifying glass and magnet. Then, place this mixture in a clean 100-mL beaker. Add 30 mL of tap water and stir. Prepare a filtration setup, filter, and record your observations.
6. Pour 10 mL of the filtrate into an evaporating dish, prepare a heating setup, and gently heat until all of the liquid is gone. Examine the residue in the evaporating dish and on the filter paper.
7. Using the crucible tongs, hold a dry piece of Magnesium ribbon in the flame. Quickly place the burning ribbon on the watch glass. Compare the appearance of the ribbon before and after burning.
8. Place the burnt remnants of the Magnesium into a clean test tube, and add 10 drops of Hydrochloric acid to it. Also, add 10 drops to the original Magnesium. Feel the bottom of each tube.
The Review on The Use of Waste Glass as Construction Material
Introduction Waste glass is of great concern in some developed countries, particularly in the urban areas. This is because of the amount of waste material generated from both municipal and construction sources, and the lack of waste disposal areas to receive the material. Countries like Japan, the United States of America, and Australia have taken the initiative to invest in the recycling of glass ...
9. Put some sugar in a clean test tube and heat it. Watch for changes and periodically check for odors. Record your results.
10. Scrape some of the sugar residue into a clean test tube and add 3 mL of water to test its solubility. Record your results. Then add 5 drops of Hydrochloric acid to it and feel the bottom of the tube.
11. Add 5 drops of Hydrochloric acid to the test tube with the Sodium Bicarbonate dissolved in water. Feel the bottom of the tube and note the collection on the sides.
12. Place the sample of the Iron and Sulfur mixture into a clean test tube. Heat it vigorously for several minutes. Submerge the hot test tube into water. Test it for magnetism.
Data and Observations:
Data Table 1: Physical Properties of Matter
Substance Physical State Color Odor Solubility Magnetism
Sulfur solid yellow none partially no
Iron solid brown rusty metal yes yes
Sodium Bicarbonate solid white none yes no
Sodium Chloride solid white none yes no
Sugar solid white sweet yes no
Sand solid tan none partially no
Magnetism solid silver metallic no no
Data Table 2: Observation of Physical and Chemical Changes
System Observations
Iron and Sulfur mixture with magnet Only the iron is magnetic; Sulfur is less clumpy
Sodium Chloride and sand mixture
With water –
Filtered –
Evaporated –
No reaction
Sand stays in the filter
Water evaporates; Salt stays in dish
Magnesium burned in air Burns bright white
Magnesium reacted with acid Temperature rises a little; Fizzes
Combusted product reacted with acid Temperature rises a lot; Fizzes
Sugar heated Smelled like burnt marshmallows; Smoked; Turned black
Sodium Bicarbonate Temperature rises a little; Droplets form on inside of tube
Calculations:
There were no calculations made in this lab.
Conclusion:
Physical changes do not change the properties of the individual substances. Chemical changes will affect the properties.
The Essay on Test Tube Starch Solution Water
Detection of Biological Molecules Introduction: Without carbon, nitrogen, hydrogen, sulfur, oxygen and phosphorus, life wouldn't exist. These are the most abundant elements in living organisms. These elements are held together by covalent bonds, ionic bonds, hydrogen bonds, and disulfide bonds. Covalent bonds are especially strong, thus, are present in monomers, the building blocks of life. These ...
