The aim of this experiment was to understand the relationship between the variables of Ohm’s law and how they are part of an operation of an electric circuit. Introduction:
This experiment was done in two parts. The first part consisted of understanding how to determine the current, voltage and resistance as part of Ohm’s law. The second part consisted of how to use the variables in an electrical current. Knowing how the variables are used in calculations and electrical currents is important in determining the value of the resistor and how it affects the current in the circuit.
A device known as the multimeter is used to find the voltage and current in the circuit. Ohm’s principal discovery was that the amount of electric current through a metal conductor in a circuit is directly proportional to the voltage impressed across it, for any given temperature. Ohm expressed his discovery in the form of a simple equation, describing how voltage, current, and resistance interrelate: V= IR equation (1)
This continuous movement of free electrons through the conductors of a circuit is called a current (I).
Current is often referred to in terms of “flow. The force motivating electrons to “flow” in a circuit is called voltage, which is a specific measure of potential energy which is always relative between two points. When there is a certain voltage present within the circuit it means the measurement of how much potential energy exists to moves the electrons from one particular point in the circuit to another particular point. Free electrons tend to move through conductors with some degree of friction, or opposition to motion.
The Term Paper on Relationship Between The Current And Voltage
Aim: To investigate the relationship between Current and Voltage Scientific Knowledge The current and voltage of an electric circuit, is given by the formula V = IR. This is known as Ohms. Ohms Law is only applicable, when the temperature of the resistor is kept constant. Therefore Ohms law is only applicable to Ohmic conductors. An example of Ohmic conductors are metals and alloys at constant ...
This opposition to motion is more properly called resistance. The amount of current in a circuit depends on the amount of voltage available to motivate the electrons, and also the amount of resistance in the circuit to oppose electron flow. Just like voltage, resistance is a quantity relative between two points (cramblet, boorn, crowell, and starck).
There are two types of circuits namely, series and parallel. In a series circuit the following equations are used to calculate resistance, voltage and current: Req = R1 + R2 + R3 + ….. Equation (2) Ieq = I1= I2 = I3 …… Equation (3)
Apparatus & Procedure:
Procedure of part one of this experiment was, decode the resistance values by the colors of the five resistors available to you. Once all five have been decoded, record values in excel. Then construct a circuit using a D-cell battery, electronics lab borad and wire leads as shown in figure 3.1A. Once that has been completed, insert the red wire and black wire into the multimeter and insert the red on the positive side of the battery while making sure the black wire is in upper left section of the lab board. Keep in mind that the multimeter sensitivity should be at 200mA range.
Now you can place the restitor in the circuit to determine the readings. After determining the values of the five resistors, disconnect the multimeter in order to connect a wire from the positive end to the resistor. Make sure to change the multimeter to voltage scale and reconnect the wires as shown in figure 3.1b. Now you can measure the voltage with a resistor in the current and record these values in the table. Be sure to do this with every resistor.
Part 1 sample equations: Voltage/Resitance = Current (V/R=I).
In part two of this experiment, use the same equipment was in part one. Pick three resistors and insert them in the board as series as shown in figure 6.1 below while keeping in mind that they need to be connected with additional wires to complete the circuit. Then connect two wires to the battery cell. Put the scale back to 200mA, now that the current is complete it must be interrupted by connecting the red wire to the positive terminal. Then connect the black wire to the resistor 1 as shown figure 6.3. Record the reading of I0 which is initial current. For parallel circuit, set the board as shown in figure 6.4 below. Repeat the previous procedure, and interrupt the circuit in order to connect the multimeter at certain points in order to measure the currents of each resistor.
The Essay on Total Resistance Resistors Current Parallel
... of resistors I ... resistance of an electrical circuit, and what effects they have on the current. Variables: number of resistors series / parallel Constants: voltage length / materials of wires type / resistance ...
Data:
Table 1-Using values of current and resistors to find voltage: can be found in the appendix A of this report. Graph 1 of resistance vs current can be found in appendix A. Graph 2 of current vs voltage/resistance can be found in the appendix A. Table 2- Series circuit:
Results & Discussion:
At the start of this experiment, setting up the apparatus was a mild set back for my group as it was rather difficult to attach the wires in the correct location especially, in the parallel circuit. We quickly resolved this by seeking help to understand the setup. We were able to determine the current, voltage and resistance in each circuit and with the three resistors.
In the series circuit by looking at table 2 under appendix A, current is the same at every resistor which shows that it follows the formula for current in series circuit as current at each point is equal. However, for voltage and resistance when one increases so does the other. It can be seen as a clear trend that with increasing voltage the resistance also increases as they are directly proportional. The readings for each voltage are individual and the total resistance is found by the sum of all the resistors in the circuit.
Looking in appendix A table 3, the table shows results for parallel circuit. The currents at 0 and 4 are equal or the same. The voltage is the same when going through each resistor which follows the formula in parallel circuit that each voltage equals each other. However, the resistance the inverse of
each resistor is summed up to equal the total value of the resistance which is also inversed. Thus the total resistance would be smaller than the total summed up. Looking at graph 1 in appendix A, it can be seen that as current increases the resitance decreases which follows Ohm’s law. As, I=V/R. The graph does follow the theory of this experiment. Similarly, looking at graph2 it shows a relationship between V/R and current. Conclusion:
The Essay on Investigating Basic Circuits
Introduction What is an electrical circuit? How can you manipulate components and design a circuit that will do what you want it to? This guided activity will introduce you to some components, tools, and concepts that are fundamental in electronics. It will allow you to investigate and discover: What are voltage, current, and resistance? How are they related to one another? What are some of the ...
I can conclude that my results do agree with the theory. The results have shown that there is some type of relationship between the three variables and how they behave in a series and parallel circuit. It was also seen that the voltage and current had constant readings for different circuits. There was some difficulty in calculating the readings as it was rather difficult to do, due to human error and equipment error. The equipment should be more accurate with the readings and students should improve their handling on the equipment so as to obtain more accurate results. Ohm’s Law describes that current-voltage relationship for a resistor is linear.
Appendices
Appendix A – prediction and results of the electric field mapping. 1. Table 1 shows the universel resistor values and the recorded resistor values. 2. Table 2- shows the data in series circuit
3. Table 3 shows the data in parallel circuit
4. Graph 1 shows the relationship of current vs resistance.
5. Graph 2 shows the relationship of current vs voltage with the error bars
Appendix C- Citations of sources
Giancoli, Douglas C. Physics, Principles With Applications. 6. 2. Prentice Hall, 2005. Print. cramblet, jerry, james boorn, ben crowell, and jason starck. “Contributers:Ohm’s Law.” all about circuits. N.p., sept 2004. Web. 22 Sep. 2013. .
