Hydrochloric acid and sodium hydroxide are corrosive. Avoid direct contact. If any touches your skin, wash it off immediately. Solid sodium hydroxide is especially dangerous because it absorbs moisture rapidly from the air, forming an extremely corrosive liquid. Avoid spilling this solid, and if a spill occurs, clean it up immediately. Be sure to close the lids of bottles of sodium hydroxide securely, immediately after using. Dispose of solutions according to your teacher’s instructions. A lab coat or apron is strongly recommended. Procedure:
Part One: The Dissolving of Solid Sodium Hydroxide in Water 1. Read through the procedure and look carefully at the data tables provided for you at the end of this lab. 2. Put 200 mL of cool distilled water into your nested styrofoam cup calorimeter. Stir carefully with a thermometer until a constant temperature is reached. Measure and record this temperature. 3. Accurately find and record the mass of about 2 grams of solid sodium hydroxide. Perform this operation as quickly as possible since the solid absorbs moisture from the air very rapidly and forms a very corrosive liquid. 4.
Place the solid sodium hydroxide into the water in the cups. Stir gently with the thermometer until the solid is completely dissolved and record the highest temperature reached. 5. Discard the solution safely and rinse the cup thoroughly with water. Part Two: The Reaction of Solid Sodium Hydroxide with Hydrochloric Acid 6. Repeat steps 2-4, but replace the 200 mL of water with 200 mL of 0. 25 M hydrochloric acid. 7. Discard the solution and again rinse the cup thoroughly before proceeding to Part Three Part Three: The Reaction of Sodium hydroxide solution with Hydrochloric Acid 8.
The Essay on The Dissolving of Solid Sodium Hydroxide in Water Procedure
Measure out approximately 205 mL of distilled water and pour it into the calorimeter. Stir carefully with a thermometer until a constant temperature is reached. Record the volume of water and the constant initial temperature of the water on your data table. 2. Place a plastic measuring trough on top of the digital balance, and then zero the balance (press the tare button) so that the mass of the ...
Accurately measure 100 mL of 0. 50 M hydrochloric acid solution into your calorimeter and 100 mL of 0. 50 M sodium hydroxide into a 250 mL beaker. Both solutions should be at or near room temperature. 9. Record the temperatures and volumes of each solution. 10. Add the sodium hydroxide solution to the acid solution in the styrofoam cup. Stir the mixture with the thermometer and record the highest temperature reached. 11. Discard the solution as directed by your teacher. Calculations: 1. From your data, calculate the following for each part of the experiment.
a) The temperature change of the liquid. b) The heat absorbed by the solution. (You are to assume that the solution has a c=4. 184 J/goC c) The number of moles of sodium hydroxide present. For Parts One and Two this can be found from the grams used. For Part Three the number of moles of sodium hydroxide is found from the molarity and the volume used. d) The amount of heat evolved per mole of sodium hydroxide used. This final value is the heat of reaction. 2. The accepted value for the heat of solution of sodium hydroxide can be found in a chemistry handbook.
Compare your experimental value with this accepted value and calculate the experimental error. Questions: 1. Add the ionic equations given in the introductions for Parts One and Three. Compare the result with the ionic equation for Part Two. 2. Compare the sum of the heats of reaction for Parts One and Three with that obtained for Part Two. In the light of your answer to Question 1, explain your results here. 3. Discuss Hess’s law in terms of the law of conservation of energy and in terms of the three parts of this experiment. 4.
Suppose you had used 8 g of sodium hydroxide in Part One. a) How would this have affected the change in temperature? b) What quantity of heat would have been evolved in your reaction? c) What effect would this have had on your calculation of the heat of reaction for Part One? 5. Write the net ionic equation for Part Three of this experiment. Write the net ionic equation for the reaction between solutions of potassium hydroxide and sulphuric acid. Compare the two net ionic equations. What does the heat of reaction for Part Three of this Experiment represent.
The Essay on Precipitation Reactions
AIM: To outline what a precipitation reaction is, describe ways which one can predict whether a precipitation reaction would form or not, describe the uses of precipitation reactions in everyday activities and industries BACKGROUND INFORMATION: Precipitation is the formation of a solid in a solution during a chemical reaction, such as evaporation. A substance that causes precipitation when it is ...