ADVANCED MANUFACTURING TECHNOLOGY & AUTOMATION Coursework 2 Robotics Summary At present BL Cars Ltd manufacture a part of an automobile suspension assembly known as a Crosstube. They are considering moving from manual to robotic production in either a single cell / single robot or line / multi robot layout. The following report recommends the use of the Fanuc Arc Mate robot, which is a compact, six axis, modular-built, electric servo-driven robot which is controlled by the a R-J 3 controller with ArcTool application software. All ancillary equipment options are considered. The two layouts are considered and all health and safety implications are detailed.
The report concludes with a discussion on the validity of each layout. For low volume manufacture it is recommended that a single-cell layout is utilised. For economic production of high volumes a line layout would be the primary choice. Contents 1.
0 Introduction 2. 0 Robot Specification 2. 1 Mechanical Characteristics 2. 2 Performance Specifications 2. 3 Programming & Control Methods 3. 0 Specification Of Ancillary Equipment 3.
1 Welding Tool 3. 2 Gripper 4. 0 Robotic Assembly 4. 1 Cell Layout 4. 1 Line Layout 5. 0 Health and Safety 5.
1 Cell Layout 6. 2 Line Layout 6. 0 Discussion 7. 0 References 8. 0 Appendix 1. 0 Introduction BL Cars Ltd manufactures a part of an automobile suspension assembly.
The Term Paper on Cell Cycle
?The cell cycle, or cell-division cycle, is the series of events that take place in a cell leading to its division and duplication that produces two daughter cells. In cells without a nucleus, the cell cycle occurs via a process termed binary fission. In cells with a nucleus, the cell cycle can be divided in three periods: interphase—during which the cell grows, accumulating nutrients needed for ...
It is known as a Crosstube. The complete part consists of four thin sheets of steel presswork. Two parts are identical and are positioned either end of the larger cross brace, which has been formed from two larger pieces of sheet steel… The diagram below illustrates the complete assembly: Presently the two parts making up the cross brace are secured using specific jigs. Once secure they are spot weld along the flange edges. The next step is to secure the two mounting plates to the presswork.
The process is completed by arc welding the component to add extra strength to the spot welds and secure the mounting plates. N. B. When the parts are pressed from the sheet steel locating points are incorporated. This ensures each part is located in the correct position in the jig.
The use of industrial robots is ever increasing. The robot usually does a secondary machinery operation after a primary shaping operation. When performed manually, this secondary operation often requires the operator to work in an unpleasant environment, to carry out a repetitive and tiring task with bulky tools. BL Cars Ltd is considering using robots to automate the Crosstube assembly process. The robots will be used for material handling, spot and arc welding in one of two contrasting layouts: 1. Single-cell, single robot – low volumes 2.
Line-layout, multi-robot – high volumes Compared to manual welds, robot welds provide the following benefits: A higher quality weld Greater consistency Increase arc on time as a proportion of total time Increased operator safety Automatic weld quality monitoring. Compared to manual handling, robots handling provides the following benefits: Greater consistency Greater accuracy Increased repeatability Low running costs 2. 0 Robot Specification BL Cars Ltd have decided to use the Fanuc Arc Mate 50 il. This robot is a compact, six axis, modular-built, electric servo-driven robot which is controlled by the R-J 3 controller with ArcTool application software.
The robot has been designed to maximise throughput and use of floor space by providing a compact, high speed design in a proven and reliable mechanical unit. Fanuc Arc Mate 50 il Price: Single robot 30, 000 Mechanical Characteristics The robot has six axes of movement. The diagram below illustrates axis movement: The diagram below illustrates the floor space required for mounting: Physical dimensions Performance Specifications Programming & Control Methods The majority of MIG welding jobs are conducted manually. It is relatively recently that machines have come on to the market with sufficient positional repeatability to automate the process reliably and flexibly.
The Essay on Part Time Faculty Tenure Education
Introduction The increasing use of non-tenure-track faculty began in the 1970 s as a response to projected enrollment declines and continued in the following decades based upon budgetary constraints. Over the last thirty years non-tenure faculty has grown from 22 percent in 1970-71 to over 50% percent by 2001. Part-time faculty holds an estimated 43 percent of faculty appointments and non-tenure- ...
Arc welding using MIG is a complex multi-variable control task. Therefore is imperative that an effective controller is chosen. The controller BL Cars LTD has chosen to use is the R-J 3 shown below: FANUC Robotics’s YSTEM R-J 3 Controller uses advanced technology packaged in a proven, reliable third generation controller design. Process capability and open architecture features improve application and motion performance while simplifying system integration. SYSTEM R-J 3 incorporates FANUC Robotics’ unique “plug-in-options” concept which allows the flexibility for applications specific configurations while maintaining a commonality for all users of the system. Features: 32-bit main CPU with dual processor architecture permits fast calculations, reduces program execution times and increases path accuracy Provides extensive line of compact I/O modules for both digital and analogue signals Allows for fast power-up and program execution with auto resume after cycle start High-speed, precision control of up to 6 axes of motion Auxiliary axes options can support up to three separate motion groups, each with its own control program and simple kinematic models Advanced communications and networking capabilities include built-in Ethernet and PCMCIA interface Accu Path provides enhanced path tracking during linear and circular motion while minimizing speed variations Collision detection minimizes potential damage to the robot or end-of-arm tooling Collision detection minimizes potential damage to the robot or end-of-arm tooling Use of surface mounting and 3-D packaging reduces components and increases reliability Quick change servo amplifier reduces maintenance time Distributed I/O options reduce cabling costs and simplify troubleshooting Increased use of fiber optics simplifies connections and enables faster communications Increased use of fibre optics simplifies connections and enables faster communications Multi-tasking operating system allows execution of several concurrent user programs Instant trigger response ( 4 ms) increases repeatability and improves process control.
The Essay on Robot Operating System (ROS)
I have visited the Industry Academia Cooperation Fair on last Thursday and Friday. I had a good experience there and improved a lot of knowledge from it. These are some pictures in this exhibition. 1. Research about ROS I think the lecture TORK(Tokyo Opensource Robotics Kyokai Association) provided is very interesting and significant, which talked about ROS(Robot Operating System) in details. 1.1 ...
Benefits: Reduces capital expenses: -Modular package allows rotator to be added only if needed -Eliminates expensive tools typically required to trim parts -Reduces number of robots required to achieve a target throughput Increases throughput and quality up to 35% over competitive robotic tracking systems and manual welding Adaptive well bias optimists weld wire positioning to fill lap joint gaps without reducing travel speeds (100 inches per minute) Root Pass Memorization (RPM) allows users to perform multi-pass welds without re tracking. 3. 0 Specification Of Ancillary Equipment Welding Tool BL Cars have two options: 1. Use senseless robots and relatively precise tooling, better jigs, and more efficient transportation. This method reduces dimensional variation.
2. Use a robot and sensor system to locate the start and end points of each weld. This method also traces the seam steering the weld torch, and as a result reduces the error. Precise tooling is very expense.
Taking into account capital and recurrent costs BL Cars will utilise robots with sensors. Seam Tracking Sensor ‘The MIG EYE seam tracking sensor equips FANUC Robotics’ welding systems with a laser-based tracking sensor. Designed specifically for arc welding sheet metal stampings, MIG EYE locates weld seams and provides real time control of the robot’s path to maintain proper alignment between weld wire and joints.’ The aim of this equipment is to maximise the quality and the speed of the weld. Assuming BL Cars Ltd choose to integrate this tool with an ARC Mate robot and Arc Tool software, MIG EYE reduces total programming time, enhances uptime and increases throughput for a wide variety of welding systems. The illustration below shows a tool which incorporates a sensor and MIG welder. Figure 2 torch / sensor package (57 mm Diameter) Handling Tool To automate the line layout a handling tool is required.
The tool will be used to hold the job whilst it is welded. It is necessary to consider the shape, orientation, weight, and the centre of gravity of the part. Once these variable have been determined an appropriate gripper can be selected. For photograph of chosen tool, and further information on handling tool application software please refer to appendix 1. 4. 0 Robotic Assembly A robotic assembly cell is an independent unit consisting of one or more robots and associated peripheral equipment, by means of which a complete product can be assembled as far as possible.
The Term Paper on The Cell Phone Revolution
Since the beginning of the industrial revolution, the world has become a smaller place. The time used to travel to far distances has diminished; with the growth of new technologies, traveling and communicating have become simple daily tasks for many people. Through the growth of global communication, people have become closer to others across the globe, and business has gone world wide. One ...
Relatively long cycle times Relatively large number of various parts assembled per robot In the automotive industry the ratio of assembly cells to assembly lines is approximately 2: 1. Cell Layout The diagram below illustrates a simple cell layout. Robotic Assembly Line A line layout comprises two robotic stations which are installed in series. The cycle times are relatively short, and also a limited number of parts per station and product transport between stations. Line Layout The diagram below illustrates possible line layout: Financial Considerations Set-up costs are greater in a line layout since there are two robots and extra ancillary equipment. However all line layout is capable of significantly higher throughput levels.
Therefore if high volume manufacture is required a line layout will be the most economic option, providing a lower overhead cost / unit . 5. 0 Health and Safety When implementing any form of system within a manufacturing environment it is imperative that all health and safety implications are taken into account and the appropriate precautions are incorporated. The majority of accidents involving robots have occurred: 1. Whilst an operator is programming 2. Whilst conducting experimental robot sequences 3.
Whilst an operator is adjusting and / or maintaining peripheral devices 4. As a result of poor provision or installation of safety equipment From the above information it is apparent that when setting up a robotic cell it is important to consider 1. Operator safety whilst programming and / or maintaining the robotic system 2. Equipment protection. With robot systems, the type of robot, its use and its relationship to other plant will all influence the design and selection of safeguards. Any safeguard chosen must permit the required operations to be conducted and where necessary, teaching, programming, setting, maintenance and trouble-shooting operations to be carried out.
The Essay on Load Cell System Data Cells
Biologics and Contract Manufacturing Company ensures batch control system data accuracy Precision Pharma Services, Inc. is a new business a biological products facility originally started in 1979 as part of the Greater NYC Blood Program. The FDA approved facility has been operational in the production of blood products for the past decade and has been a privately held company since 2001. With ...
Prior to safeguard design all hazards and injury risks must be identified. In this case a single robot cell will require a different level of safeguarding to a multi robot line layout. Perimeter fencing will be used to protect all members of staff from the equipment line. The fencing will consist of a hollow section steel framework in filled with mesh. All sections will be 2 m high and securely fastened to the framework Where there is a danger of molten metal and welding flash infringing regulations, the filling between the framework will be manufactured from sheet steel. A sliding access gate will be located either side of the line to allow for regular access.
A presence sensing device will be linked to the control system to instantly cut power to all machinery within the restricted area. Cell Layout Specific An operator will be working with the robot within the cell. Therefore it is important that suffi ent safety devices are incorporated within the cell to ensure operator safety. Four emergency stop buttons will be strategically positioned in and around the cell to allow emergency shut down in the event of a problem.
An escape path and guidelines will be displayed outside the cell to highlight to the operator the action that should be taken if the robot goes out of control. Pressure mats will be placed around the robot. When pressure is applied to the mat the system is shut down. An alarm system will also be incorporated within the system to indicate human presence. The operator within the cell will always have ultimate control over robot activity. Infra-red curtains are flexible and reliable and make an excellent method of operator protection.
Line Layout Specific Whilst operating under normal conditions its is unlikely that a robot will require manual human input. In addition to the general safety precautions, it is necessary to consider the possibility of the two robots damaging themselves and other equipment. This will be achieved by using positive stops which limit the movement of the robot to part of its envelope. Trip devices will be utilised to stop the robot if it comes into contact with people or other equipment A trapped key exchange will be used to secure all gates.
The Essay on Product Line Additions Products Variety Costs
Assis ng Product Line Additions: Managers must identify the situations in which variety is an important competitive variable, examine the relationship between variety and cost, understand the underlying determinants of cannibalization and complementary, and asses the consequences of not responding to competitive innovations. Conjoint analysis is useful for managers who evaluate new product line ...
This system will positively isolate the power supply to all parts of the robot installation. There is a lock on all perimeter gates and a lock on an isolator controlling the robot actuators. The key cannot be removed from the lock to open the gate unless the system is in a safe state. 7. 0 Discussion The crosstube is mass produced, i. e.
high volumes are required. The most cost effective layout choice would be the line-layout. Although higher set-up costs are involved initially the cost of implementing cells with an equivalent rate of throughput would be greater. However it is likely that this product will move into decline and the number of these products demanded will fall. When this occurs the line layout could be abandoned, the space utilised for a part in growth, and a single cell could be established for dedicated production of the cross tube. BL Cars Ltd must consider using robots cell for the economic manufacture of prototype and growth products.
As growth slows and a product is nearing maturity a line-layout can be considered (volume determined) This method of assembly would be partially useful in the decline period of the products life cycle, as the cell would be capable of producing other similar parts or parts within the product family. 8. 0 References web Rooks. B. , Rover 75 Sets New Standard In Body In White Assembly. International Journal, Vol.
26, Is 5, 1999 Bromley. J. S. E. , Davey. P.
G. , V idler. A. R. , Clocks in.
W. F. , Morgan. C.
G… An Implementation of Model Based Visual Feedback for Robot Arc Welding of Thin Sheet Steel. International Journal of Robotics Research Vol. 4 No.
1 1985 Asf ahl. R. C. 1992. Robots and Manufacturing Automation. John Wiley Rampersad.
H. K. 1994. Intergrated and Simultaneous Design for Assembly. John Wiley 317.
